SP100 SeriesRead this manual carefully before use and always follow the • instructions.Keep the manual in a convenient place for easy reference.• If y
10Quick adviserThe quick adviser (under the lid on the sewing machine) provides various descriptions such as basic machine operations.Accessing the qu
211Before use (Be sure to read this section before use)How to operate foot controllerOperation Be sure to use the main power switch to turn off the s
2121Sewing preparationsConnecting the powerDo not touch the power plug with wet hands.Doing so could cause an electric shock.Hold the power plug, to r
14Winding the lower thread112Turn off the sewing machine.910Return the thread 1winding spindle by sliding it in the direction of the arrow.Note If th
215Sewing preparationsPull the thread from the thread spool, and then hold it with one hand while passing it around the thread guide with the other ha
162Threading the lower threadOpen the bobbin case cover, and insert the bobbin into the bobbin case.If the bobbin is incorrectly inserted into the bob
217Sewing preparations6Pass the thread through A, then B, and then pull the thread to the rear, as shown below.Pull out about 15 cm of thread to the r
18Threading the upper thread1279Turn off the sewing machine.Raise the presser foot lever.Pass the thread through the needle thread guide.The thread ca
219Sewing preparations6Turn the handwheel towards yourself to raise the take-up lever.Pull the thread from 1the thread spool, and hold it with one ha
123452ContentsBefore use (Be sure to read this section before use)Important safety instructions • ... 3How t
20Using the needle threaderBefore using the needle threader, use the main power switch to turn off the sewing machine.Not doing so could cause an inju
221Sewing preparationsUsing the needle threader z12While fully lowering the needle threader lever, hook the thread on the guide as shown in the diagra
22Pulling up the lower thread12Raise the presser foot lever. Loosely hold the upper thread with your left hand, and then turn the handwheel towards yo
223Sewing preparationsApplication of each stitch patternTurn the handwheel towards yourself to raise the needle in the highest position.Turn the patte
2412Changing the presser footRemoval zPress the presser foot holder lever in the direction of the arrow to release the presser foot.Raise the presser
225Sewing preparations2Installation z1Position the presser foot pin directly below the groove in the presser foot holder.Lower the presser foot lever
262Changing the needle1Correct needle selection zIf a faulty needle is used, not only could it impair the sewing performance, but it could also damage
227Sewing preparationsRelationship between the needle, thread and fabric, and adjusting the thread tensionThe quality of the sewing finish will improv
32821SewingStraight stitching and reverse sewingStraight stitch z1Position the fabric and lower the presser foot lever.Step on the foot controller to
293SewingThread cutter zReverse sewing is performed while pressing down the reverse sewing lever.Stitch 1 cm from the edge of the •fabric to prevent
113Before use (Be sure to read this section before use)Before use (Be sure to read this section before use)Important safety instructionsThese safety i
30Sewing thick fabric zWhen sewing over thick fabric, the presser foot may tilt and be unable to feed through the fabric.Fabric or thick paperSewing f
313SewingSewing tube-shaped fabrics z11Pull out the extension table (accessory box) in the direction of the arrow.12Sew tube-shaped fabrics such as tr
32112Zigzag sewingThere are various zigzag applications, such as applique and overcasting.1Position the fabric and lower the presser foot.Step on the
333SewingAdjusting thread tensionAdjustment method for upper thread tension zUpper thread is tightWrong sideRight sideUpper thread is looseUpper threa
3411234Buttonhole sewingButtonhole sewing to match the size of the button is possible.For stretch fabric or thin fabric, it is recommended to use a st
353Sewing76 Raise the needle to the highest position, set the pattern dial to “4”, and sew 5 to 6 bar-tack stitches.Raise the needle to the highest po
368Use the buttonhole cutter to cut the center, making sure not to cut the stitches.Note:If a marking pin is put in the bar-tack area it helps to prev
373Sewing1OvercastingThis is a sewing method that prevents unraveling at the edge of the fabric.8822Change to the zigzag sewing foot or the overcastin
382178Zipper insertionSewing the left side of the zipper z88Position the fabric so that the zipper is on the right side of the presser foot.ZipperSet
393Sewing8Sew until just before the presser foot makes contact with the slider, and then stop the sewing machine.6878SliderSewing the right side of th
4Before using the sewing machine make sure that the presser foot holder clamp screw, needle clamp screw and needle plate screw are rmly tightened, an
401112At the tacking or the crease that was ironed, fold back the fabric so that wrong side faces upward.Sew overcasting along the edge of the fabric,
413Sewing667Lower the presser foot, and start sewing. The part of the stitch that catches the fold will be visible from the right side of the fabric.
424MaintenanceFeed dog and hook maintenanceIf the sewing machine makes a loud noise or rotates slowly, there could be thread waste or dust in the hook
434MaintenanceRemove any lint or dust from the feed dog and hook, and then wipe them with a soft cloth.A vacuum cleaner can be used to remove lint and
44Right side of bobbin case zAttaching the Bobbin Case1Position the bobbin case so that part a on the bobbin case is below part b on the sewing machin
454MaintenanceAttach the needle plate with red mark a on the bobbin case positioned as shown in the diagram.6Tighten the needle plate screws.1Attach
46Changing light bulb81Loosen the screw with a + screw driver of your own, and take off the face cover in the direction of the arrow.82Turn the light
474MaintenanceServicing double-insulated products (230V-240V)In a double-insulated product, two systems of insulation are provided instead of groundin
48Trouble Cause Countermeasure PageNeedle keeps breakingNeedle incorrectly inserted into the machineInsert the needle correctly 26The needle clamp scr
494MaintenanceTrouble Cause Countermeasure PageThe fabric wrinkles / puckersThe tension of the upper thread is too tightAdjust the thread tension 33Th
15Before use (Be sure to read this section before use)Do not drop or insert any foreign objects into any openings such as opening space when you remov
550OthersRecyclingWe are committed to the protection of the environment. We strive to minimize the environmental impact of our products by continuousl
515OthersSpecicationsSP100 SeriesModel XXX15C XXX15D/SuperJ15Hook type HorizontalNeedle Home-use sewing machine needle (HA-1)Bobbin TOYOTA-exclusive
Web: www.home-sewing.com Head Ofce Avenue de l’Industrie 21, Parc Industriel, 1420 Braine-L’Alleud BELGIUM T
6Part namesThread guideTake-up leverFace coverThread cutterLight bulb Extension table (Accessory Box)Bobbin case coverBobbin caseFeed dogNeedle plateN
17Before use (Be sure to read this section before use)Thread winder guideHandwheelMain power switchTerminal boxThread cutterButtonholeadjustment screw
8Part names and their functionsThe various parts of the sewing machine have the functions described below.Extension table (Accessory Box)Presser foot
19Before use (Be sure to read this section before use)Reverse sewing leverHandwheelUse the handwheel to manually raise and •lower the needle.Note: Al
Komentáře k této Příručce